# Battery ratings

Because batteries create electron flow in a circuit by exchanging
electrons in ionic chemical reactions, and there is a limited number of
molecules in any charged battery available to react, there must be a
limited amount of total electrons that any battery can motivate through a
circuit before its energy reserves are exhausted. Battery capacity
could be measured in terms of total number of electrons, but this would
be a huge number. We could use the unit of the *coulomb* (equal to 6.25 x 10^{18}
electrons, or 6,250,000,000,000,000,000 electrons) to make the
quantities more practical to work with, but instead a new unit, the *amp-hour*,
was made for this purpose. Since 1 amp is actually a flow rate of 1
coulomb of electrons per second, and there are 3600 seconds in an hour,
we can state a direct proportion between coulombs and amp-hours: 1
amp-hour = 3600 coulombs. Why make up a new unit when an old would have
done just fine? To make your lives as students and technicians more
difficult, of course!

A battery with a capacity of 1 amp-hour should be able to continuously supply a current of 1 amp to a load for exactly 1 hour, or 2 amps for 1/2 hour, or 1/3 amp for 3 hours, etc., before becoming completely discharged. In an ideal battery, this relationship between continuous current and discharge time is stable and absolute, but real batteries don't behave exactly as this simple linear formula would indicate. Therefore, when amp-hour capacity is given for a battery, it is specified at either a given current, given time, or assumed to be rated for a time period of 8 hours (if no limiting factor is given).

For example, an average automotive battery might have a capacity of
about 70 amp-hours, specified at a current of 3.5 amps. This means that
the amount of time this battery could continuously supply a current of
3.5 amps to a load would be 20 hours (70 amp-hours / 3.5 amps). But
let's suppose that a lower-resistance load were connected to that
battery, drawing 70 amps continuously. Our amp-hour equation tells us
that the battery should hold out for exactly 1 hour (70 amp-hours / 70
amps), but this might not be true in real life. With higher currents,
the battery will dissipate more heat across its internal resistance,
which has the effect of altering the chemical reactions taking place
within. Chances are, the battery would fully discharge some time *before* the calculated time of 1 hour under this greater load.

Conversely, if a very light load (1 mA) were to be connected to the battery, our equation would tell us that the battery should provide power for 70,000 hours, or just under 8 years (70 amp-hours / 1 milliamp), but the odds are that much of the chemical energy in a real battery would have been drained due to other factors (evaporation of electrolyte, deterioration of electrodes, leakage current within battery) long before 8 years had elapsed. Therefore, we must take the amp-hour relationship as being an ideal approximation of battery life, the amp-hour rating trusted only near the specified current or timespan given by the manufacturer. Some manufacturers will provide amp-hour derating factors specifying reductions in total capacity at different levels of current and/or temperature.

For secondary cells, the amp-hour rating provides a rule for necessary charging time at any given level of charge current. For example, the 70 amp-hour automotive battery in the previous example should take 10 hours to charge from a fully-discharged state at a constant charging current of 7 amps (70 amp-hours / 7 amps).

Approximate amp-hour capacities of some common batteries are given here:

- Typical automotive battery: 70 amp-hours @ 3.5 A
*(secondary cell)* - D-size carbon-zinc battery: 4.5 amp-hours @ 100 mA
*(primary cell)* - 9 volt carbon-zinc battery: 400 milliamp-hours @ 8 mA
*(primary cell)*

As a battery discharges, not only does it diminish its internal store of
energy, but its internal resistance also increases (as the electrolyte
becomes less and less conductive), and its open-circuit cell voltage
decreases (as the chemicals become more and more dilute). The most
deceptive change that a discharging battery exhibits is increased
resistance. The best check for a battery's condition is a voltage
measurement *under load*, while the battery is supplying a
substantial current through a circuit. Otherwise, a simple voltmeter
check across the terminals may falsely indicate a healthy battery
(adequate voltage) even though the internal resistance has increased
considerably. What constitutes a "substantial current" is determined by
the battery's design parameters. A voltmeter check revealing too low of a
voltage, of course, would positively indicate a discharged battery:

Fully charged battery:

Now, if the battery discharges a bit . . .

. . . and discharges a bit further . . .

. . . and a bit further until its dead.

Notice how much better the battery's true condition is revealed when its voltage is checked under load as opposed to without a load. Does this mean that its pointless to check a battery with just a voltmeter (no load)? Well, no. If a simple voltmeter check reveals only 7.5 volts for a 13.2 volt battery, then you know without a doubt that its dead. However, if the voltmeter were to indicate 12.5 volts, it may be near full charge or somewhat depleted -- you couldn't tell without a load check. Bear in mind also that the resistance used to place a battery under load must be rated for the amount of power expected to be dissipated. For checking large batteries such as an automobile (12 volt nominal) lead-acid battery, this may mean a resistor with a power rating of several hundred watts.

**REVIEW:**- The
*amp-hour*is a unit of battery energy capacity, equal to the amount of continuous current multiplied by the discharge time, that a battery can supply before exhausting its internal store of chemical energy. - An amp-hour battery rating is only an approximation of the battery's charge capacity, and should be trusted only at the current level or time specified by the manufacturer. Such a rating cannot be extrapolated for very high currents or very long times with any accuracy.
- Discharged batteries lose voltage and increase in resistance. The best check for a dead battery is a voltage test under load.